{"id":6802,"date":"2022-05-02T11:00:40","date_gmt":"2022-05-02T18:00:40","guid":{"rendered":"https:\/\/mitchell11.wpenginepowered.com\/blog\/shopconnection\/featured-tpms-tip-hyundai-sonata-2008-2010\/"},"modified":"2025-04-04T08:18:31","modified_gmt":"2025-04-04T15:18:31","slug":"featured-tpms-tip-hyundai-sonata-2008-2010","status":"publish","type":"shopconnection","link":"https:\/\/mitchell1.com\/shopconnection\/featured-tpms-tip-hyundai-sonata-2008-2010\/","title":{"rendered":"Featured TPMS Tip: Hyundai Sonata 2008-2010"},"content":{"rendered":"

SUBJECT VEHICLE:<\/strong> Hyundai Sonata 2008-2010<\/p>\n

RELEARN PROCEDURE?<\/strong> Yes<\/p>\n

SPECIAL TOOLS NEEDED?<\/strong> Yes, a TPMS exciter scan tool.<\/p>\n

The tire pressure monitoring system (TPMS) of the 2008-2010 Hyundai Sonata monitors the air pressure in the four road tires with wheel-mounted tire pressure sensors. To do this, the system uses a receiver, four radio frequency (RF) tire pressure sensors, a warning indicator on the instrument cluster, and a data circuit to perform system functions.<\/p>\n

When tire pressure is below the allowed threshold, the low pressure warning light on the instrument cluster will be illuminated. The receiver has an auto-learn function that takes place once per ignition cycle. Upon successful completion, the four tire pressure sensor IDs are latched into memory for monitoring. Until the auto-learn function is completed, the previously learned sensors are monitored. The receiver uses vehicle speeds of 12 mph (20 KM\/H) or more for up to 20 minutes to learn a new sensor.<\/p>\n

TPMS warning light<\/strong><\/p>\n

NOTE: Tire pressure is also dependent on temperature of the tire. Tire pressure should only be adjusted when tires are cold (about the same as ambient air temperature). When the low tire pressure warning light comes on, check the air pressure of all tires and adjust to specification. If the tire is damaged, repair as necessary. Ensure the warning light goes off. If the warning light is still on, there is a malfunction in the TPMS. See appropriate manufacturer service information.<\/p>\n

Reset procedures<\/strong><\/p>\n

NOTE: If the tire pressure sensor is replaced, it will need to be initiated. The TPMS is not affected by wheel and tire rotation. When the low tire pressure warning light comes on, check the air pressure of all tires and adjust to specification. Ensure the warning light goes off.<\/p>\n

Tire pressure sensor initiation<\/strong><\/p>\n

NOTE: In the following procedure, a TPMS exciter scan tool must be used.<\/p>\n

NOTE: When four sensors have been learned as road wheels, it is not possible to learn new road wheel sensors on the same ignition cycle.<\/p>\n

NOTE: Do not perform this procedure if the vehicle is parked on a metal floor, roof or on an alignment rack or lift. The metal will transfer the RF signals, which can cause the learn procedure to fail and set diagnostic trouble codes (DTCs).<\/p>\n

NOTE: The sensor\u2019s default state will be Storage Auto (High Line).<\/p>\n

1) Using TPMS exciter, change the sensor mode to Normal Fixed Base (Low Line). See Figure 1.<\/p>\n

NOTE: Sensors which were already configured as Base (Low Line) will take longer to read.<\/p>\n

2) Holding the TPMS exciter within three inches (76 mm) of the sensor valve, read each tire pressure sensor ID in the following order: front left, front right, rear left, then rear right.<\/p>\n

3) Connect the TPMS exciter to Data Link Connector (DLC) located under left side of instrument panel. Register the four sensor IDs to the receiver (see Figure 2 and Figure 3).<\/p>\n

NOTE: The TPMS receiver will complete the learn procedure of the new sensor after the vehicle is driven up to 20 minutes at speeds over 12 mph (20 KM\/H).<\/p>\n

4) Cycle Ignition, wait four minutes and check that \u201cNORMAL RECEIVER STATE\u201d is now displayed.<\/p>\n

Demounting\/mounting procedures<\/strong><\/p>\n

CAUTION: The tire should be demounted from the wheel using the tire changer manufacturer\u2019s instructions. Use the following information to avoid damage during the demounting\/mounting procedures.<\/p>\n

CAUTION: Ensure that the wheel to be fitted is designed for the sensor mount. There should normally be a mark to indicate this. Tire pressure sensors can be used on steel or aluminum rims.<\/p>\n

NOTE: If the tire pressure sensor is replaced, it will need to be initiated. See reset procedures. The TPMS is not affected by wheel and tire rotation.<\/p>\n

Tire pressure sensor<\/strong><\/p>\n

CAUTION: Do not use puncture repair fluid, as this can cause the sensor pressure port to block and an incorrect warning to occur.<\/p>\n

Read more:<\/h4>\n